The Eureka is a professional recording channel
strip containing a discrete class A transformer-coupled microphone
preamplifier, FET compressor, and three-band parametric equalizer. The
microphone preamplifier features variable input impedance so that the
Eureka can be matched and "tuned" for all types of microphones and
recording applications. The Class A transformer-coupled microphone
preamplifier also features "SATURATE" which adjusts the drain current
on the input FET amplifier to simulate of the effects of tape
saturation and tube "warmth".
The Eureka's ultra fast FET compressor has both
soft and hard knee compression as well as a separate make up gain stage
and hi-pass side chain compression to deliver hard pumping to ultra
transparent compression and everything in between. The Eureka's
three-band fully parametric EQ gives you variable Q (bandwidth) on each
band as well as an EQ pre COMP switch to put the EQ before the
Compressor in the signal path. The equalizer has overlapping frequency
selection on each band for total tonal control and shaping.
The Eureka is loaded with microphone, line and
instrument input so you can use it as a front end preamplifier for
recording with microphones, guitars, keyboards, synths as well as a
compressor/equalizer on a single channel during mixdown. The Eureka
also has balanced send and return jacks so that you can insert your
favorite outboard processor before the compressor/EQ to further enhance
and customize your sound.
The Eureka gives you the sonic performance and
control you need in the real-world to produce professional quality
audio that you, your customers and your fans deserve!
Features
- Class A High Headroom Transformer Coupled Microphone Preamplifier
- Variable Microphone Input Impedance
- Variable SATURATE control (simulates tape saturation and tube warmth)
- Fully Variable Compressor with Hi-pass Side Chain
- Three Band Fully Parametric Equalizer
- EQ Pre or Post Compressor
- High Headroom Output Section
- Very Low Noise Design
- Internal Power Supply
- Optional 24-Bit/192k Digital Output Card
- Transparent, wide range performance
Technical Specifications
- Channels: One
- Dynamic Range: >115dB
- Headroom: +22dB
- Frequency Response: 10Hz to 50kHz
- Internal Operating Level: 0dBu = 0B
Microphone Preamp
- Gain: +12dB to +52dB
- Noise Floor: -112dBu (+12dB gain)
- EIN: -127dB
- THD + Noise (0% saturation): <0.005%
- THD + Noise (full saturation): <0.5%
- Microphone Input Connector: XLR
- Microphone Input Impedance (selectable): 2.5k, 1.5k, 600, 150, 50 Ohms
- Instrument Input Connector: 1/4" TS
- Instrument Input Impedance: 1 Meg Ohm
- Send Connector: 1/4" TRS balanced/unbalanced
- Send Output Impedance: 51 Ohms
- Return Connector: 1/4" TRS balanced/unbalanced
- Return Input Impedance: 10k Ohms
- Metering (3-LED): -20dBu, 0dBu, Clip
- Line Input (switchable): 1/4" TRS, 10k Ohm Input Impedance
- Phantom Power (switchable): +48V (pin 1, pin 2 XLR)
- Pad (switchable): 0dB/-20dB
- Phase (switchable): 0, 180 degrees
- Hi-pass filter (switchable): -3dB shelf at 80Hz
Compressor
- Threshold (variable): -40dBu to +20dBu
- Ratio (variable): 1-10 (1:1 to 2:1)
- Attack (variable): 0.1 to 200 ms
- Release (variable): 0.05 ms to 3 S
- Gain Make-up: -20dB to +20 dB
- Hi-pass Side Chain Filter (variable): 10Hz to 10kHz
- Metering: Analog VU (gain reduction / Output Level)
Equalizer
- Low Band (+/-13dB): 20Hz to 300Hz
- Mid Band (+/-13dB): 200Hz to 3kHz
- High Band (+/-13dB): 2kHz to 20kHz
- Q (variable all bands): Q=0.4 to 2 (3 octave to 2/3 octave)
Master
- Output Fader: -70dB to +10dB
- Output Connectors: XLR balanced and 1/4" TRS balanced/unbalanced
- Output Impedance: 51 Oms
- Metering (output level): Analog VU (-20dBu to +6dBu)
- Meter (gain reduction): Analog VU (-20dB to 0dB)
- Output Headroom: +22dBu
Physical
- Power Supply: Internally Regulated Linear Type
- Power Requirements (factory configured): 100VAC to 120VAC, 200VAC to 240VAC
- Size: 1U Rack
- Dimensions: 19" x 1.75" x 7"
- Weight: 8lbs
