When we decided to build a club mixer, we wanted to
satisfy club techs and DJs alike. Xone:464 naturally shares its
construction methods with our pro touring desks, so venues can depend
on it for outstanding audio and reliability.
Its
unique analogue filters and 4 band asymmetric EQ also make it an
incredibly creative tool that DJs really enjoy using. We also included
a set of 4 fully featured mic/line inputs, which is great for venues
running small live sets as well as DJs, or for those pioneering artists
who are mixing live and recorded sources.
4 Mono Inputs
XLR or TRS jack connector, gain, 4 band EQ with swept mids, HPF @
100Hz, 6 aux sends (1-4 pre, 5&6 switchable pre/post fader), pan,
peak signal led, cue and on button with led. 100mm long throw fader.
Insert point and direct output on TRS jack.
6 Dual Stereo Channels
2 stereo sources (A & B) per channel. A is on RCA for all channels
with RIAA preamps on CH 5,6,9,10. B inputs are line in on RCA CH 5
& 10 and TRS on CH 6,7, 8 & 9. Access to all 6 auxes is at the
top of the channels, leaving performance area clear. 3 colour bar meter
and gain control. Powerful 4 band EQ with on switch. 60mm fader and
X-fade assign section.
Stereo Mix Outputs
2 independent mix outputs with level controls, 12 segment 3 colour led
metering and insert. Balanced XLR plus secondary RCA outputs, plus
selectable mono out also on XLR and TRS. CH1-4 feed mix1 or mix2.
Stereo channels feed mix1 direct or via the X-fader. Mix1 can route to
mix2.
6 Auxiliary Sends
6 aux sends to [TRS] outputs for monitors or FX sends. Mic / line CH
1-4 have individual sends and stereo CH 5-10 have aux 1&2
individual mono sum and auxes 3&4, 5&6 paired with L to odd, R
to even. Aux sends 1-4 are always pre-fade, while auxes 5&6 are
switchable pre/post fader. Additional controls allow aux sends to track
the X-fader post fade.
4 Stereo 2 Mono Zone Outs
Mix1, mix2, post x-fader aux 3&4 and 5&6 can provide stereo
mixes on rotary controls. Post x-fader aux 1 & aux 2 can provide
mono mix outputs with level controls
4 Band EQ
Mono channels have 2 swept frequency mids. Stereo channels have EQ-on
switch and all frequency sections have +6dB boost to preserve headroom
and -26dB cut for creative mixing.
VCA Cross Fader
Conductive plastic, high quality 45mm Penny & Giles fader with
curve switchable to cut or dip. Stereo channels can be assigned to X
(left) side with green led indication or Y (right) side with yellow
led. VCA operation means wear and tear does not affect audio. Drop-in
replacements. Pan trim control for imbalance.
Voltage Controlled Filters
2 filters [1 for each side of the x-fader] with choice of High Pass,
Band Pass, Low Pass or multiples e.g. notch. Resonance control -
adjusts Q from ‘mild to wild’. Sweep controls from 100Hz to 20kHz with
blue led on switch.
External Input
TRS jack inputs via level control to mix1, mix2 or monitor.
Engineer / DJ’s Toolbox
2 high powered headphone outputs with level. Booth output on TRS with
level. Monitor section has 8-way switch bank to select monitor source.
12 segment 3 colour bar metering. Channel cue overrides the monitor
selected in the phones [and booth if Cue Enable is pressed]. Split Cue
sends cue signals to left and selected program to right. Mute kills
local monitor output [option for -20dB action]. Mono sum button for
phase and compatibility check.
PSU
High performance internal switched-mode power supply. Universal mains input voltage.
Configuration options
Internal links to configure mono CH aux sends to pre-EQ and / or
pre-ON. Stereo CH Cue to post EQ. Stereo CH auxes to pre-EQ. Direct out
to pre-fade. EXT in -10dBV/+4dBu. Monitor Mute to -20dB attenuator.
Remote local monitor mute. These options require competent installation
or service personnel SysLink kit – output on 25-pin D connector to link
to other A&H consoles.
Dimensions:
Desktop - 19"W x 7.6"H x 20.9"D
Rack mounted - 19”W x 17.5"H x 5.3”D
